Серия QL
Technical Specification of QL/CL
*1) Это максимальное количество устройств, отображаемое в разделе ONLINE DEVICE LIST на экране DANTE SETUP. С помощью консоли можно подключить только те устройства, которые есть в списке.
*2) Каждое рэковое устройство в окне REMOTE HA ASSIGN поддерживает до 32 каналов
General Specifications QL5/ QL1
QL5 | QL1 | ||
---|---|---|---|
Частота дискретизации | Внутр. | 44.1kHz / 48kHz | 44.1kHz / 48kHz |
Внешн. | 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) | 44.1kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm), 48kHz: +4.1667%, +0.1%, -0.1%, -4.0% (±200ppm) | |
Задержка сигнала | Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz | Less than 2.5ms, INPUT to OMNI OUT, Fs= 48kHz | |
Фейдер | 100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders | 100mm motorized, Resolution=1024steps, +10dB to –138dB, –∞dB all faders | |
Коэффициент нелинейных искажений | Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min. | Less than 0.05% 20Hz-20kHz@+4dBu into 600Ω, INPUT to OMNI OUT, Input Gain= Min. | |
Диапазон воспроизводимых частот | +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT | +0.5, -1.5dB 20Hz-20kHz, refer to +4dBu output @1kHz, INPUT to OMNI OUT | |
Динамический диапазон | 112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min. | 112dB typ.: DA Converter / 108dB typ.: INPUT to OMNI OUT, Input Gain = Min. | |
Уровень собственного шума | Эквивалентный шум на входе | -128dBu typ., Equivalent Input Noise, Input Gain=Max | -128dBu typ., Equivalent Input Noise, Input Gain=Max |
Остаточный выходной шум | -88dBu, Residual output noise, ST master off | -88dBu, Residual output noise, ST master off | |
Перекрестные искажения | -100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min. | -100dB*1, adjacent INPUT/OMNI OUT channels, Input Gain = Min. | |
Требования к питанию | 100-240V 50/60Hz | 100-240V 50/60Hz | |
Потребляемая мощность | 200W | 135W | |
Размеры | Ш | 828mm(32.6in) | 468mm(18.4in ) |
Высота | 272mm(10.7in) | 272mm(10.7in) | |
Глубина | 563mm(22.2in) | 562mm(22.1in) | |
Вес без упаковки | 21.8kg(48.1lb) | 14.7kg(32.4lb) | |
Аксессуары | Owner’s Manual, dust cover, power cord, DVS license sheet, Nuendo Live | Owner’s Manual, power cord, DVS license sheet, Nuendo Live | |
Опции | Mini-YGDAI cards *2 , Gooseneck Lamp LA1L | Rackmount kit RK1, Mini-YGDAI cards *2 , Gooseneck Lamp LA1L | |
Прочее | Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃ | Operating temperature range: 0 - 40℃, Storage temperature range: -20 - 60℃ |
- Crosstalk@1kHz : A 22kHz, 30dB/Oct filter is used to measure crosstalk.
- Total Harmonic Distortion : An 80kHz, 18dB/Oct filter is used to measure total harmonic distortion.
- Hum & Noise : An A-Weight filter is used to measure hum & noise.
Analog Input Characteristics
*1. The sensitivity is the input level required for output at +4dBu (1.23V) or at the defined level when all the faders and level
controllers are set to the maximum value.
*2. XLR-3-31 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*3. 0dBu=0.775 Vrms for all specifications.
*4. All the AD converters use 24-bit linear/128-times oversampling.
*5. The INPUT connectors have +48V DC (phantom power) jacks, each of which can be turned on/off individually from the console software.
*6. QL1: INPUT1-16
Analog Output Characteristics
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
*2. The PHONES connectors for stereo headphones are balanced jacks (Tip=LEFT, Ring=RIGHT, Sleeve= GND).
*3. 0 dBu=0.775 Vrms for all specifications.
*4. All the DA converters use 24-bit linear/128-times oversampling.
*5. The console has an internal switch for toggling the maximum output level.
*6. This is a value measured with the PHONES LEVEL knob set to 10 dB below the maximum position.
*7. QL1: OMNI OUT 1-8
Digital Input/Output Specifications
*1. QL1: 32ch Input/32ch Output@48kHz
Digital Output Specifications
*1. XLR-3-32 connectors are balanced jacks (1=GND, 2=HOT, 3=COLD).
I/O SLOT (1-2) Specifications
Each I/O Slot accepts a Mini-YGDAI card.
Only Slot 1 has a serial interfac
Control I/O Characteristics
*1. Input pin: TTL level, w/ internal pull-up (47kΩ) Output pin: Open drain output (Vmax=12V, maximum sink current/pin=-75mA) Power supply pin: Output voltage Vp=5V, Max. output current=300mA
*2. 4 pin=+12V, 3 pin=GND, Lamp nominal power: 5W, Brightness (voltage) can be adjusted from the software.